登录    |    注册

您好,欢迎来到中国测试科技资讯平台!

在线投稿 专家审稿 编辑办公 咨询评价
首页> 《中国测试》期刊 >本期导读>基于安装误差的导引头隔离度测量值修正

基于安装误差的导引头隔离度测量值修正

59    2019-11-28

0.00

全文售价

作者:周永恒, 崔少辉, 方丹

作者单位:陆军工程大学石家庄校区, 河北 石家庄 050003


关键词:红外导引头;隔离度测量;安装误差建模;误差补偿


摘要:

为提高红外导引头隔离度的测量精度,结合导引头测试系统原理,分析红外导引头安装误差对隔离度测量值的影响。利用多体建模理论构建红外成像导引头安装误差模型,推导由安装误差所引入的导引头视线角速度测量误差,并对该误差所导致的导引头隔离度测量值的误差进行了仿真分析。最后,利用误差模型对隔离度测量值进行补偿,并利用半实物仿真系统进行实物测试,得到补偿前隔离度测量值为1.034%,由安装误差引起的测量值误差为0.129%,补偿后隔离度值为0.902%。测试结果表明了该方法的可行性,对解决红外成像导引头隔离度的高精度测量具有参考意义,为红外成像导引头的试验评估提供了理论基础与技术保障。


Research on the method of measuring the angle rate accuracy of infrared seeker
ZHOU Yongheng, CUI Shaohui, FANG Dan
Army Engineering University Shijiazhuang Campus, Shijiazhuang 050003, China
Abstract: To improve the measurement accuracy of the infrared seeker isolation, based on the principle of the seeker testing system, this paper had analyzed the influence that the installation error of the infrared imaging seeker has on the measured value of the isolation. The multi-body modeling theory had been used to construct the infrared imaging seeker installation error model. The error of the sight-angle rate measurement for the seeker caused by the installation error had been derived, and a simulation analysis had been conducted on the error of the seeker isolation measurement value caused by the error referred before. Finally, the measurement value of isolation degree is compensated by error model and tested by hardware in the loop simulation system. The measurement value of isolation degree before compensation is 1.034%, the measurement value error caused by installation error is 0.129%, and the isolation degree after compensation is 0.902%. To conclude, the testing result illustrates the feasibility of this method, which has great significance on solving the high-precision measurement for the isolation of the infrared imaging seeker, thus providing a theoretical basis and technical guarantee for the experimental evaluation of the infrared imaging seeker.
Keywords: infrared seeker;isolation measurement;installation error modeling;error compensation
2019, 45(11):21-25  收稿日期: 2018-06-18;收到修改稿日期: 2018-11-02
基金项目:
作者简介: 周永恒(1994-),男,四川资阳市人,硕士研究生,专业方向为装备仿真测试、分析
参考文献
[1] 张义广, 杨军, 朱学平,等.非制冷红外导引头成像导引头[M].西安:西北工业大学出版社, 2009:15-29.
[2] 刘永昌. 红外成像导引头性能评估系统技术探讨[J]. 红外与激光工程, 1995(1):1-4
[3] 马庆恒, 李怀东. 反坦克导弹导引体制发展综述[J]. 国防技术基础, 2003(4):34-35
[4] DAVID F, JAMES M.Generic models in the advanced IRCM assessment model[C]//Proceedings of 2001 Winter Simulation Conference, 2001:789~796.
[5] 张文杰.基于贝叶斯神经网络的红外空空导弹抗干扰性能评估[D].长沙:国防科技大学, 2015.
[6] 朱华征, 范大鹏, 马东玺, 等. 导引头伺服系统隔离度与测试[J]. 光学精密工程, 2009(8):1994-2000
[7] 李富贵, 夏群利, 蔡春涛,等. 导引头隔离度寄生回路稳定性及测试方法[J]. 北京理工大学学报, 2013(8):801-806
[8] 孟令东.光电系统稳定精度测量方法研究[D].哈尔滨:哈尔滨工业大学, 2008.
[9] 张安峰.光电稳定系统的稳定精度测试研究[D].长春:长春理工大学, 2002.
[10] 崔莹莹, 夏群力, 祁载康. 导引头稳定平台隔离度模型研究[J]. 弹箭与制导学报, 2006, 26(1):22-25
[11] 徐平, 王伟, 林德福. 导引头隔离度对末制导炮弹制导控制的影响[J]. 弹道学报, 2012, 24(1):17-22
[12] 杨勇. 偏心安装的导引头隔离度测量值的修正[J]. 电讯技术, 2016, 12(56):1335-1340
[13] 赵世明. 红外制导半实物仿真误差分析[J]. 红外与激光工程, 2017, 46(8):1-6
[14] 李岩, 范大鹏. 光电稳定机构指向误差建模与敏感度分析[J]. 国防科技大学学报, 2008, 30(1):104-109
[15] 庞振基, 黄其圣. 精密机械设计[M]. 北京:机械工业出版社, 2000:321-324.